Get Started

 

 

We've unearthed this article involving How to Install a Bathtub down the page on the internet and thought it made sense to discuss it with you over here.

Mounting a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging project. If the old tub is readily easily accessible, the task can move immediately; if you need to open a wall to eliminate the old bathtub and position the new tub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Make certain you have certified yourself for the work and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to consider using one before you start. Chances are you might need an expert plumber to make tube links.
This write-up will certainly help you mount a new bathtub in your shower room if you have currently purchased a new bathtub and do not need to transform the plan of your previous water supply pipelines.
Your tools as well as material list should consist of the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Getting ready for the Installment

First of all, the sustaining structure provided with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to prevent stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its last setting.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be quite troublesome because of the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Setting up the Bath tub

Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to make certain that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water and check all joints and new pipework for leaks as well as tighten them if required. Fill up the tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the producer's user's manual. Tiling and also securing around the bath tub must wait until the bathtub has been used at least when as this will certainly settle it into its final position.

 

 

Fitting New Touches

If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the area where the bathroom fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can split rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof adhesive and also cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I found that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the internet. Appreciated our write-up? Please share it. Let another person discover it. I love reading our article about How to Install a Bathtub Yourself.

Visit Our Website